 |
|
|
|
Wrist
Bands
Stretch
wrist bands
 crocheted
stretch cloth band with 5 silver plated conductive
monofilaments- 18mm wide
- anti-allergenic
backplate
- 3mm stud
with 360 swivel
- soft,
durable, comfortable to wear
Slimline
Ergo wrist band
- jewelry-quality
stainless steel
- 10mm wide,
weighs only 24g
- easliy
adjustable from 130-170mm using one or more of the five
10mm nylon expansion links
- 3mm stud
with 360 swivel
- super-durable
quality
Ergo wrist
band
 jewelry-quality
stainless steel- 18mm wide,
34g
- easily
adjustable from 130-170mm using one or more of the five
10mm nylon expansion links
- 3mm stud
with 360 swivel
- super-durable
quality
|
|
Grounding
Cords
- 100%
retraction
- 1 Mohm
resistor
- 3mm snap
- banana
plug / alligator clip termination or 4,5 or 7mm
snap termination
|
|
Bench
Mat Ground Cords
These take care of the proper grounding of the operator
and worksurface mat. By using an Adapt-A-Snap additional
personnel can quickly plug into the ESD safe
workstation and can be properly grounded
- 450cm
straight grounding cord
- quick
release snap with full 360 swivel
- dark blue
- 1 Mohm
resistor
|
|
Adapt-a-Snaps
The
Adapt-A-Snap attached to a Common Point Ground unit or to an
existing grounding point allows additional personnel to plug
into the same ground connection.
|
|
EBP
Bar
-
yellow
ABS with black print
-
two
4mm plug sockets and one 7mm male stud
-
each
grounding point is connected with 1 Mohm resistor
-
straight
grounding cord of 2m with a 5mm ring terminal
-
complies
with IEC 61340-5-1
|
|
Shoe
grounders
Shoe
grounders can be used to ground operators standing or
walking on ESD safe floors or floor mats. IEC 61340-5-1
requires shoe grounders to be worn on both shoes.
- reinforced
black conductive rubber
- proper and
reliable contact with the conductive floor or floor mat
- easy to
fit and adjust
- non-marking
on floor or shoe
- fit on
every shoe
- large
knitted ribbon contact tab with 1 Mohm resistor
Heel
grounder
- quick
release buckle
- unique
elasticized rear section provides fit and comfort to all
shoe types and sizes
- bright red
heel band for clear identification
Toe
grounder 
- for pumps
or high heels
- unique
elasticized rear section provides fit and comfort to all
shoe types and sizes
- bright red
heel band for clear identification
|
|
Conductive
disposable shoe covers
Operators
wearing conductive shoe covers will be permanetly grounded
via the conductive floor mat or floor.  Conductive
shoes or heel grounders are not necessary. The grounding tab
is worn in shoe or sock and makes contact with the skin.
NeutroStat
Boots
-
for
permanent grounding
-
re-usable
-
easy
to wear
-
packed
per 300ea
|
|
Ground
Check Grounding tester
The
GroundCheck is a dependable easy-to-use test mechanism for
personnel grounding devices. It meets the requirements of
IEC 61340-5-1 prescribing that grounding products should be
tested on their critical parameters daily.
 pass
indicated by a visible and audible signal, high fail and
low fail by a visible signal- test range
750 Kohms - 35 Mohms
- 20V test
voltage
- accuracy
+/- 10%
- supplied
with calibration certificate
- uses a 9V
alkaline battery
- indicator
for low battery
- 7mm press
stud, 4mm plug socket, 6mm stud for alligator clip
- size 6,8 x
11,5 x 2,5 cm
- complies
with IEC 61340-5-1
- CE
compliant
|
|
Ground
Check Backplate
In
combination with a Backplate the GroundCheck can be used as
a central grounding tester at the entrance of the EPA.
- printed
with clear test instructions
- 4 and 10mm
connecting point for grounding cords
- 10mm press
stud for connection to the Footplate
- size 30 x
20cm
- 4 mounting
screws are included
|
|
Ground
Check Footplate
The metal
Footplate can be used in combination with the GroundCheck
and the Backplate for testing of shoe grounders and
conductive footwear.
- 10mm press
stud
- 200cm
straight wire with 1 Mohm resistor for connection to the
Backplate
- size 15 x
30cm
|
|
Ground
Check Calibration Monitor
The
GroundCheck Calibration Monitor was designed to monitor the
GroundCheck SC1815GC to be working within the parameters of
IEC 61340-5-1.
- 4 test
positions : low fail, low pass, high pass, high fail.
- size 6,8 x
11,5 x 2,5 cm
- CE
compliant
|
|
Constant
Wrist Strap Monitor
The Constant
Wrist Strap Monitor continuously measures the operator's
wrist strap and ground connection.
- pass
indicated by a green LED flash, fail indicated by an
audible signal and a red LED flash
- 9V DC
adapter, 110V AC 300ma
- test
voltage nominal 7,5V
- accuracy
+/- 5%
- weight 85g
- size 8 x
5,6 x 2,5cm
- CE
compliant.
|
|
|
